Deluxe Panel Cart
The WoodRiver® Deluxe Panel Cart makes it very easy to get your material from your truck bed or trailer to your table saw with minimal effort. The tilting carriage adjusts from a low horizontal height of 31-1/2" to a maximum 39-1/2" to fit most table saws. The large frame adjusts from...
The WoodRiver® Deluxe Panel Cart makes it very easy to get your material from your truck bed or trailer to your table saw with minimal effort. The tilting carriage adjusts from a low horizontal height of 31-1/2" to a maximum 39-1/2" to fit most table saws. The large frame adjusts from 18" wide x 36" tall to 18" wide x 45" tall to support even full 4 ft. x 8 ft. sheets of plywood. Pivoting feet can be stowed out of the way when the cart sits idle and then locked in position to quickly go to work carrying the next load. The lower cart assembly uses two 4" locking swivel casters and two 4" swivel only casters to provide rolling support to a compact but sturdy 16"-wide x 18-long frame that very easily fits through doors as narrow as 24". Don’t worry about loading down this cart because it will comfortably move up to 250 pounds of sheet material.
- A safe and efficient way to transport your sheet goods to your table saw or your workbench for processing
- Feet can be stowed out of the way when the cart sits idle to reduce cart’s footprint
- Tilting carriage adjusts to match the height of your table saw
- Able to support a full sheet of plywood, MDF, etc.
- Two 4" locking swivel casters and two 4" swivel-only casters provide rolling support
- Tilting carriage adjusts from a low horizontal height of 31-1/2" to a maximum 39-1/2" height
- Large pivoting frame adjusts from 18" wide x 36" tall to 18" wide x 45" tall
- Compact but sturdy 16" wide x 18" long frame fits through doors as narrow as 24"
- Comfortably move up to 250 lb of sheet material
- (1) WoodRiver - Deluxe Panel Cart
Articles & Blogs
Before you tackle the spring cleaning, organization and renovation projects at your house this year, check out some of the tools, accessories and supplies at Woodcraft that will save time and cut stress.
asked woodworker Dave Clarke, who was diagnosed with ALS in 2018, to take a look at an article Woodcraft
Magazine published in Issue 44 by Pete Stephano – “The Wheelchair
Woodworker Shop” – to see if he felt that the recommendations were still
relevant and if he had any other advice for folks wanting to set up a workshop
with modifications. Read more here...
Customize your outdoor living space and enhance your home’s curb appeal with a new landscaping plan, colorful door treatments, more furniture or a fresh coat of paint for outdoor structures. Woodcraft can help you with tools, supplies and how-to resources to create an appealing and functional family “hangout.”
Nice Compact Cart
The cart comes nearly preassembled. It took about 5 minutes or less to unbox it and put it together. The directions were easy enough to follow although the 1st step showed a picture of the bolts for the connecting bar in the wrong location. The bolts on my cart were shipped in the connecting bar itself. I was somewhat skeptical about how sturdy it would be as the base is 16" deep and a little less than 18" wide. So far it seems sturdy and rolls well on my laminate shop floor. You just need make sure the panel is centered on the brackets. It has adequate support when the 4' x 8' panel is on the cart in both the horizontal and vertical positions. The Pivot Lock seems a bit stiff but that should loosen up with time and usage. The cart has 2 locking wheels of the 4 wheels that keep the cart in place reasonably well. There are some items that could use improvement. When the cart is adjusted to my table saw height the panel brackets are about 12" off the ground. This makes loading a full 3/4" panel from ground level to the brackets by yourself a little awkward. The panel brackets themselves need the edges rounded a bit or a nylon glide with rounded edges attached on them to make loading/unloading and protecting the panel edges better. Additionally, the bolts for the brackets need to be unscrewed almost entirely to swing the brackets out of the way. A solution may be to have the brackets mounted just on the inside of the lower part of the tube frame with a different style knob. The knob could be a changes out for a T shaped repositionable one. Overall I am pleased with the purchase. It is a good value for the money.